Differences between revisions 1 and 11 (spanning 10 versions)
Revision 1 as of 2009-11-03 04:18:37
Size: 223
Editor: SamatJain
Comment:
Revision 11 as of 2021-11-01 21:59:06
Size: 2385
Editor: SamatJain
Comment:
Deletions are marked like this. Additions are marked like this.
Line 1: Line 1:
## page was renamed from CheatSheet/mdadm

<<TableOfContents>>

== Creation ==

See also [[CheatSheet/Partitioning]].

{{{#!highlight sh numbers=off
# New Linux RAID encompassing the entire disk
sudo sgdisk --largest-new=1 --typecode=fd /dev/disk-dev-device

# RAID 5 array creation
sudo mdadm --create /dev/md5 --level=5 --assume-clean --raid-devices=3 /dev/sd{d,e,f}1

# Create a high-performance RAID10 array (2x read speed compared to RAID1)
sudo mdadm --create /dev/md6 --level=10 -p f2 --assume-clean --raid-devices=2 /dev/sd{i,k}1

# Save configuration (not necessary)
/usr/share/mdadm/mkconf > /new/etc/mdadm/mdadm.conf
}}}

== Performance ==

=== Stripe cache size ===

Increase 1 MiB default to 16 MiB (№ 4K blocks):

{{{#!highlight sh numbers=off
echo 4096 | sudo tee /sys/block/md0/md/stripe_cache_size
echo 4096 | sudo tee /sys/block/md1/md/stripe_cache_size
}}}

=== Write-intent bitmaps ===

[[https://raid.wiki.kernel.org/index.php/Bitmap|Write-intent bitmaps]] speed-up RAID resyncs significantly, at the expense of a little write performance.

{{{#!highlight sh
# Create write-intent bitmap
mdadm --grow --bitmap=internal /dev/mdX

# Remove write-intent bitmap
mdadm --grow --bitmap=none /dev/mdX
}}}
Line 7: Line 52:
{{{#!highlight sh {{{#!highlight sh numbers=off
Line 10: Line 55:

== Recovery ==

=== Inactive array ===

If an array comes out as inactive, e.g.:

{{{
md8 : inactive sdp1[0](S) sds1[4](S) sdx1[2](S) sdj1[1](S)
      7814054094 blocks super 1.2
}}}

Stop the array before we continue to work on it.

{{{#!highlight sh numbers=off
mdadm --stop /dev/md8
}}}

First, use examine the array components and figure out which component is out of sync (it's best to do this manually). Then, with the remaining components, reassemble the array. E.g. if /dev/sds1 was the bad device:

{{{#!highlight sh numbers=off
mdadm --assemble /dev/md8 /dev/sd{p,x,j}1 --force
}}}

to restart the array. If supposedly bad device is fine, go ahead and re-add it:

{{{#!highlight sh numbers=off
mdadm --manage /dev/md8 --add /dev/sds1
}}}

== btrfs ==

{{{#!highlight sh numbers=off
# btrfs RAID0
mkfs.btrfs -d raid0 /dev/sd{b,c}1
}}}

Creation

See also CheatSheet/Partitioning.

# New Linux RAID encompassing the entire disk
sudo sgdisk --largest-new=1 --typecode=fd /dev/disk-dev-device

# RAID 5 array creation
sudo mdadm --create /dev/md5 --level=5 --assume-clean --raid-devices=3 /dev/sd{d,e,f}1

# Create a high-performance RAID10 array (2x read speed compared to RAID1)
sudo mdadm --create /dev/md6 --level=10 -p f2 --assume-clean --raid-devices=2 /dev/sd{i,k}1

# Save configuration (not necessary)
/usr/share/mdadm/mkconf > /new/etc/mdadm/mdadm.conf

Performance

Stripe cache size

Increase 1 MiB default to 16 MiB (№ 4K blocks):

echo 4096 | sudo tee /sys/block/md0/md/stripe_cache_size
echo 4096 | sudo tee /sys/block/md1/md/stripe_cache_size

Write-intent bitmaps

Write-intent bitmaps speed-up RAID resyncs significantly, at the expense of a little write performance.

   1 # Create write-intent bitmap
   2 mdadm --grow --bitmap=internal /dev/mdX
   3 
   4 # Remove write-intent bitmap
   5 mdadm --grow --bitmap=none /dev/mdX

Diagnosis

Examine array component

Displays superblock information, including last event, RAID UUID, other components, etc.

mdadm --examine /dev/sda1

Recovery

Inactive array

If an array comes out as inactive, e.g.:

md8 : inactive sdp1[0](S) sds1[4](S) sdx1[2](S) sdj1[1](S)
      7814054094 blocks super 1.2

Stop the array before we continue to work on it.

mdadm --stop /dev/md8

First, use examine the array components and figure out which component is out of sync (it's best to do this manually). Then, with the remaining components, reassemble the array. E.g. if /dev/sds1 was the bad device:

mdadm --assemble /dev/md8 /dev/sd{p,x,j}1 --force

to restart the array. If supposedly bad device is fine, go ahead and re-add it:

mdadm --manage /dev/md8 --add /dev/sds1

btrfs

# btrfs RAID0
mkfs.btrfs -d raid0 /dev/sd{b,c}1


CategoryCheatSheet

SamatsWiki: CheatSheet/LinuxSoftwareRAID (last edited 2021-11-01 21:59:06 by SamatJain)